This website uses cookies to ensure you get the best experience on our website. Learn more

How to remove a broken bolt in a deep hole | remove broken bolt in recessed hole

x
  • How to remove a broken bolt in a deep hole | remove broken bolt in recessed hole

    13:39

    It can be difficult removing a broken bolt or stud that is recessed in a deep hole as there are not many techniques to remove the bolts. Before attempting to remove any bolt, it is a good idea to shock the bolt first, then apply some heat and finally some spray penetrant (once it is cool). Drilling out the bolt is one of the few options that will work in this scenario. In this video I show two techniques that could potentially work when a bolt is broken in a deep hole or a bolt is sheared in an aluminium component.

    Some more videos that might be of interest are-

    How to remove a rounded Allen head bolt-
    How to remove a stripped screw-
    How to remove a broken bolt-
    How to remove a rounded nut or bolt-
    Screw extractors | Easyouts -
    Removing a broken bolt using a welder-
    Remove a broken bolt using a left handed drill bit-


    How to make the bolt drill guide can be seen here-

  • x
  • HOW TO REMOVE A BROKEN BOLT DEEP IN A HOLE / REMOVE A BROKEN BOLT IN A RECESSED HOLE EASY EXTRACTION

    8:41

    HOW 2 AF how to remove a broken bolt deep in a hole. It's easy to remove a broken bolt in a recessed hole using Harbor Freight Screw Extractor kit.
    Drilling out the center of the broken bolt that is stuck in the hole. The drill bit must be in the center of the broken stud or bolt. I started with the smallest drill bit and worked up to larger size to match the No 3 extractor. Extracting a steel bolt out of aluminum cylinder head. Broken valve cover bolt easy out with this extractor kit. Keep checking the depth of the hole to the extractor don't want to drill too deep. Once the extractor starts to bite onto the broken bolt or stud soak it with lubricant and use steady force turning it out.

  • x
  • How to remove broken bolt in deep / recessed hole

    14:33

    And what to do when removal fails

  • How To Remove Broken Bolt In A Deep Hole | Magic Way To Extract Broken Screw ,Stud,Screw + Drill

    2:42

    Subscribe:

    =====================================

    This bolt is actually #torquetighting time is #broken So the bolt broken part is very tight inside the hole

    The bolt size 8mm
    This method is good and simple because this video is original
    Steps
    ♂ The #Bolt Part Is Not Visible From The Outside
    This Method Can Be Used This Type Situations At Times Like This

    ♂ Make a hole first
    That hole should also be the half size of the bolt size
    Eg: Here taken 4mm bit for 8mm blot

    ♂ After the hole making
    Bring the #machine reverse condition
    ☞︎︎︎No damages in Bolt thread that so no damages in inner threas☜︎︎︎

    ✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰✰

    Best video:
    Camera:
    My tripod:

  • x
  • Extract Broken bolts from deep hole NEW easy WAY

    13:30

    My bolt extractors are collecting dust. If you don't own a welder, this trick will pay for itself in one go. This is the first time I've ever shown this trick and I have never seen anyone else use the copper pipe. However, I'm sure someone out in the vast world has also come up with the idea as well and will quickly point it out to me. This is my go to method but there are still scenarios where a reverse drill bit would be my first choice as that is probably the quickest. However if those don't bite I move onto the welder/copper pipe.


    Get your own reverse drill bits:


    With Mig or Flux:
    Do it just like I show and don't burn away your copper. Go slow. On bolts over 1/2-5/8 you can also insert a steel pipe/tube inside your copper. Weld down the center and weld the steel pipe to the bolt. The copper will protect the threads. You don't need to fill the entire center to the top, just enough to bond the steel tube to the bolt. Twist out the steel tube/bolt assembly. This works best with large bolts.



    With stick welder:
    The flux helps insulate the sides. If the hole is large enough(1/2+ bolt), insert a copper pipe to protect the threads and then a steel pipe inside the copper. You jamb the electrode down inside the steel and the rod will weld itself and the steel tube to the bolt. Throw a pipe wrench on the steel tube and pull it out. The larger the hole the better this method works. You can use this method with smaller bolts and just the copper but you have to be a GOOD stick welder.



    STAY UP TO DATE BETWEEN PROJECTS on Social media





    SUPPORT THE CHANNEL?
    I'm not asking for people to send me anything, but people are awesome and asking how they can support the channel:

    Zero Cost to you; Watch my videos or buy any items you were going to purchase on Amazon anyways by first clicking through my affiliate link. Costs you nothing but I get a few cents for referring you to Amazon:

    OR support the SHOP DOG
    Buy Ginger a new bone:

  • How to remove any broken bolt/stud

    3:11

    tool needed
    ????
    Quick video on how to remove any broken bolt or stud
    Vid#1
    Want to see a second part? Leave a comment below ????

    My IG: 13b_dorito

    Here is some useful links for tools that you need to get this job done and that you will need on any other projects you might have!!

    my go to scanner ????

    Scanners that i own and recommend ????












    Head bolts for the LT engine left side driver side the one with the black Allen bolt ????


    Chevy LT solid lifters make sure you look up it fits your chevy LS LT engine????


    This one here is my go-to head set gasket kit all you need to re install the heads works for me on tahoe,silverado, suburban!!????


    AFM DOD lifter with spring acDelco ????


    My go-to favorite powerful impact gun cheaper nd better than milwaukee ????



    swivel sockets ????

    metric socket kit ????

    wrench set ????

    brush kit ????

    double side ratchet wrench
    ????

    impact better than snapon and cheap
    ????

    better nd cheaper than snap on
    ????

    Jack stands ????

    ratchet set ????

    what i use to record the video

    ????

    DISCLAIMER: This video and description contain affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows me to continue to make videos like this. Thank you for the support!

  • x
  • Remove a broken bolt using a left handed drill bit

    4:11

    Removing a broken bolt or stud can be extremely difficult but in some cases such as when the bolt head has been sheared off by sideways force it is possible to remove the remainder of the bolt using a left handed drill bit. Here we demonstrate how to remove a broken stud using the left handed drill bit method.

  • How to Remove a Rounded Bolt or a Broken Bolt in a deep hole

    11:14

    In this video i show you how to Remove a rounded bolt head .

    I also show you
    1. How to remove a rounded nut
    2. How to remove a rusted bolt without rounding it off
    3. How to remove a bolt with no head
    4. How to to use a bolt extractor
    5. How to remove stuck or seized bolts with heat and WD40
    6. how to use a left handed drill bit
    7. How to remove a broken off bolt in a deep hole

    Rounded bolt removal is a tedious job so as broken bolt removal. Here in this video i show you my top 5 tools to remove rounded bolts so hopefully this will be a guidance for those in need of a little helping hand.

    Bolt Extractor Set
    Bolt Extractor Set ( Low Profile )
    Bolt Extractor Set ( Deep Socket)
    Adjustable pliers
    Hammer
    Cold chisel
    Manual impact driver
    Impact wrench
    Spiral Extractor and Drill Bit Set
    Extractor wrench set
    Multi-Spline Screw Extractor Set
    Striking cap screwdriver set (cheap set)
    Square shaft extractors

    Straight teeth bolt Extractor Socket Set

    And don't forget to follow me on Instagram for more updates

  • How To Remove a Busted Bolt FAST! New Style Screw Extractors

    6:24

    This DIY video shows you how anyone can remove a broken bolt with some easy methods with this awesome set of screw extractors.

    ***************************************
    If you would like to help us out.

    ***************************************

    Tools USA

    Venom

    Dewalt

    High-Quality Drill Bits

    Screw Extractors we used in Video

    These 2 Below work great as well.
    (Good) Screw Extractors

    (Best) Screw Extractors

    Center Punch Set

    Ballpeen Hammer

    Needle Nose Grip Set

    Cresent Wrench Set

    Spin-Off
    _____________________________________
    UK Tools

    Dewalt

    Screw Extractors

    Drill Bits

    Center Punches

    Vise Grips

    Venom Gloves



    *****Disclaimer*****
    Due to factors beyond the control of SWEET PROJECT CARS, we cannot guarantee against the improper use or unauthorized modifications of this information. Make sure you check with your manufacturer to make sure this will not affect your factory warranty. SWEET PROJECT CARS assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. SWEET PROJECT CARS recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of SWEET PROJECT CARS, no information contained on this YouTube channel shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not SWEET PROJECT CARS.

  • x
  • How to remove a broken bolt 4 different ways!

    11:21

    This video shows how to remove a broken bolt using 4 different methods-

    1. Knocking the bolt round in an anti-clockwise direction with a chisel or centre punch.
    2. Welding on a nut.
    3. Drilling a hole and using a easy out/screw extractor.
    4. Left handed drill bit.


    Removing broken bolts can be challenging but in most cases the job can be done quickly and efficiently. The worst case scenario is that you have to drill the bolt out completely and re-tap the hole or use a thread insert kit.

  • How to drill out a broken tap | drill out a broken screw extractor

    15:43

    In this video I drill out a broken tap using a JCB diamondtech holesaw. Drilling out a broken tap or drilling out a broken screw extractor is often very difficult and most people would get the broken tap or broken screw extractor spark eroded. There are not many drill bits that will drill HSS taps or screw extractors as they are harder than most drill bits, but the JCB Diamondtech holesaws slowly remove the hard steel. The Diamond Tech holesaw cost £17.50 from Toolstation (I’m not on commission)


    Some more videos that might be of interest are-
    How to remove a broken bolt which is deep in a hole -

    How to make the bolt drill guide can be seen here-

    How to remove a rounded Allen head bolt-
    How to remove a stripped screw-
    How to remove a broken bolt-
    How to remove a rounded nut or bolt-
    Screw extractors | Easyouts -
    Removing a broken bolt using a welder-
    Remove a broken bolt using a left handed drill bit-

  • How Extract A Broken Bolt, Never Use A Broken Bolt Extractor & Drill. Here it is an amazing method!

    32:44

    On This Video We Showing: The owner of this truck started this job, they were trying to replace the thermostat housing, but in the process of doing it, they broke one of the bots; they try to use a drill bit to remove the bolt but they couldn't remove it, they brought it to me and ask if I can remove that broken bolt; my answer was yes, but not with the drill. so I tell them the reason Why You Shouldn't Never, Never Use A Drill. To Extract A Broken Bolt.
    Sometimes When the bolts are too rusted they are hard to remove, and most of the times break,
    We use a different method than the use of drill bit and the twisted extractor tool, because, even if you drill a straight hole all the way throughout the bolt. but if the bolt got a corroded thread it will be so difficult to remove, and you might break the extractor tool too; which will make it more difficult to remove it.
    here Is Another Extracting Bolts Video.

    Thank You For watching my videos.
    Thank you for all the comments.
    I Appreciate the calls that lots of people Throughout the USA makes to my phone number, thanking me for record and upload my videos, it makes me feel proud, that I am helping people to save or to make some money.
    I am making my videos with lots of love and with the meaning of helping you people.

    If you found this video and it was useful,
    Please Like It, And Subscribe To My Youtube Channel.
    So you can help me,
    And I can upload more videos.
    Thank you.

    ( Take this daily and you will never be sick again.
    Toma esto a diario y nunca más volverás a estar enfermo.
    Deleted YouTube video links.
    Enlaces de los videos que YouTube quito.

    Complete video, This is my way of expressing to everyone how much I appreciate you
    THIS WILL CEASE THE FEVER IN 15 MINUTES OR LESS AND WILL NOT RETURN.
    Video completo, Esta es mi forma de expresar a todos lo mucho que los aprecio
    ESTO CESARÁ LA FIEBRE EN 15 MINUTOS O MENOS Y NO VOLVERÁ.


    In 15 Minutes This Formula Will Stop The Fever And Will Not Return.
    En 15 minutos, esta fórmula detendrá la fiebre y no regresará.


    Listen To The Full Recovery Testimony Of This NHS Doctor in London, UK.
    Escuchen el testimonio de completa recuperación de este médico del NHS en Londres, Reino Unido.


    Testimony of the deleted video that YouTube doesn't want you to see.
    Testimonio del video eliminado que YouTube no quiere que veas.
    )

    Thank you for choosing our services.
    We always do our best to serve you better and fix your car properly.
    Your Friendly Expert Automobile Repair Technician.
    With more than 30 years of working in the auto repair field.

    Gabriel Auto technician
    413 Highway 100,
    Laguna Heights, TX.
    956 346 3484.

    Auto Repair Shop.
    Auto Air Conditioning Repair and Recharge
    Brakes,
    Tune-Ups,
    Radiators,
    Shock Absorbers,
    Water Pumps,
    Timing Belts,
    Oil Change,
    Fan belts,
    Struts,
    Suspension,
    Transmission Service,
    Computer Diagnostics,
    Paint and Bodywork.
    Iron Welding.

    I have more than 40 years working on cars
    I am working on cars since they have contact points ignition
    and carburetors when most of the built cars came with no air conditioning.

    We Are Here To Help With All Your Auto Repair Needs.
    We have the knowledge and the tools to do the job right.

    Gabriel Auto Technician
    413 Hwy 100,
    Laguna Heights. TX
    956 346 3484.

    Thank You for your like on our page @


    Subscribe To My Youtube channel@




  • How to remove broken bolt tracktor engine in deep hole

    2:41

    How to remove broken bolt tracktor engine
    Thanks for watching

  • Removing broken bolts

    18:53

    In this video I go through removing broken bolts. This involves using a variety of extraction tools, welding a nut, using vice grips etc.

    If you are enjoying this channel, please consider making a donation to or become a Patreon of Dangar Marine at

    T-shirts and other merchandise available at
    Post photos of you wearing your shirt to @dangarstu on Instagram!

    Dangar Marine is proudly sponsored by MarineEngine.com. MarineEngine.com supplies a wide variety of spare parts for many brands of outboard motors, be sure to check out their online store.

    All music available at

  • Deep In Hole Broken Bolt Removal

    12:23

    Extractor Set Irwin
    1/32 to 5/8 Drill Press Keyless Chuck
    Left Handed Drill Bit Set
    Irwin Extractor Set 5 Piece Set
    Ultimate Handyman Video Very Good
    In this video I show you how to make a sleeve to thread into a hole to help you drill out a broken bolt.
    Ultimate Handyman
    Help support Doublewide6 Repairs LLC by sponsoring his Patreon account


    Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

  • Tricks for removing stubborn or broken bolts | Hagerty DIY

    5:33

    Losing your mind because the only thing holding up your project is a seized bolt? Davin Reckow is here to show you the tools and techniques you’ll need to get those frustrating bolts out of the way. Whether you’re a practiced wrench in the garage or a newcomer, it’s always good to know how to get over those project roadblocks.

    Subscribe! |

    Visit our website for daily automotive news, cars stories, reviews, and opinion:

    Stay up to date by signing up for our email newsletters here:

    Talk to other car people on our community:

    Follow us on social media:
    Facebook |
    Instagram |
    Twitter |

    If you love cars, you belong with us. Hagerty Drivers Club is the world’s largest community for automotive enthusiasts. Members enjoy valuable automotive discounts, exclusive events and experiences, roadside service created specifically for collector vehicles, and a subscription to the bimonthly Hagerty Drivers Club magazine. Join Hagerty Drivers Club here:

    Like what you see? Watch our other series including:
    Redline Rebuild | Engine Time-lapse videos from start to finish
    Barn Find Hunter | Tom Cotter searches the country for abandoned cars
    Hagerty's Daily Driver | Industry news, buzz, and interviews
    Chip Foose Draws a Car | Reimagining popular cars with new designs

    Contact us:
    Suggest and feedback - tips@hagerty.com
    Press inquiries - press@hagerty.com
    Partnership requests - partnerships@hagerty.com

  • Screw extractor | easyout | broken bolt removal

    5:34

    Get screw extractors here
    Screw extractors are often called easyouts, these can be used to remove a broken bolt or a broken stud from a tapped hole. Here we demonstrate how to use the screw extractor to remove a broken bolt from a shaft. Brought to you by

  • How to remove a broken bolt in a deep hole. AJ the Automobile Engineer..

    3:26

    how to remove a broken bolt in a deep hole.

    Welcome to AJ the Automobile Engineer channel Our channel include of guiding videos :-

    You are interested in hand work, craft or you just have nothing to do, haven't you ? You have found the channel you really need. Here you can find lots of crafts, hand made items, and the main thing is that they all made of make shifts and at the lowest cost..!

    ***Thank you so much for the support and do not forget to subscribe to my channel***
    Thanks for watching the video.

    Subscribe :-

    Have a good day.

    AJ the Automobile Engineer..

  • One way how to extract a broken screw + drill and torx key.

    2:24

    Method to extract a broken screw from the inside of a car piece using a torx wrench.

  • How to Remove a Broken Bolt or Broken Screw

    5:15

    Did you break a bolt or screw and now you can't get it out? The fix is simple, just use an easy out to remove it. Easy Outs are simple to use and work fast. Drill a hole and screw in the Easy Out. Boom.

    This video shows you how to fix this problem real fast using the Easy Out.

    There are two types of Easy Outs and this one is the best for broken bolts. Another kind is the screw extractor and is best for stripped heads on screws.

    Find us at Twitter
    Look for us on Facebook
    Catch us at Instagram cleanslatefarm
    Visit the website

    Available at our Amazon Shop Neiko Screw extractor for bolts, Screw extractor for burred screw heads, Stanley Center Punch, Ryobi 18V ONE+ Drill/Driver

    Thanks for watching and supporting Clean Slate Farm. Please subscribe and hit the thumbs up! We appreciate it.

  • x
  • Removing Broken Fasteners -EricTheCarGuy

    29:19

    I think this has been one of the most requested videos ever. I think if you spend any time at all repairing vehicles, you will eventually run into this problem. There are many different ways of dealing with it and I cover most of those in this video. The focus however, is on drilling and tapping out the broken fastener. Yes, there are other methods that are not demonstrated in this video, and I may make videos specifically on those methods at some point in the future. One method I forgot to mention was welding something onto the broken fastener so that you could turn it out. I meant to mention that, but forgot. For now, I think this will help you if you find yourself dealing with a broken fastener. I wish you luck no matter what method you choose.

    Another option mentioned in the comments is left handed drill bits. They also have these with a special remover built into the bit. This is something I haven't used in the past and I don't currently own a set, but many have stated that it is another option for removing broken fasteners. There's a link below to these tools.

    Lots of links for you with this one.

    Using a Torch:

    This is where the engine cam from:

    Tools

    Drill:

    Angle Drill (pneumatic):

    Angle Drill (electric):

    Left Handed Drill Bits:

    Screw Extractor Set:

    Broken Spark Plug Remover:

    Bolt gauge:

    Tap and Die Set:

    Tap sockets:

    Center punch:

    Drill Bits:

    Drill bit sharpener:

    Punch set:

    Hammer:

    Vice Grips:

    Safety glasses:

    Easy outs:

    Easy out drill bits:

    Discussion about this video:

    The best place for answers to your automotive questions:

    Facebook:

    Twitter:

    Google+:

    Information on Premium Membership:

    Stay Dirty

    ETCG

    Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

  • How to Drill Out a Broken Bolt or Stud

    3:58

    Video tutorial on how to drill out a broken and clean out the threads using a tap. This is one of the many methods for dealing with broken bolts, you can also weld on a nut, drill the center and use an extractor, grab the remaining stud from the backside using interlocking pliers, etc.

    Website:
    Patreon:
    Facebook:
    Twitter:
    Instagram:
    Tumblr:
    Pintrest:

    Tools/Supplies Needed:
    -drill
    -drill bit set
    -tap set
    -center punch
    -hammer
    -file
    -safety glasses
    -cutting fluid

    Procedure:
    Starting with the first one, you may need to flatten out the surface which can help when making a center mark. This isn’t always possible, depending on where the bolt broke. Considering this is on a bracket that isn’t very rigid, I placed a metal wedge behind the bracket to prevent any flexing or vibrating.

    Using a center punch, mark the center of the bolt. This can be sometimes tricky, especially when you’re working in awkward positions. If the mark is off, angle the punch to push the center mark over.

    First starting with a center drill. A smaller drill bit can be used, but there may be too much flex so you can risk breaking the bit or having it wander. A center drill is much more rigid which allows for accuracy. A cutting oil or fluid does help with lubrication, keeping the bit cool and preventing it from burning out.

    Once that center has been made, move up the correct sized drill bit. You can use an indexing chart that determines the size of the drill bit required for the size of the bolt used. Use an indexing chart to determine what size drill bit is required for the threaded hole. This is where you’ll need to know the bolt size. You can go with a slightly smaller bit just to ensure you’re centered. Left-handed drill bits can also be used, these would turn in the counterclockwise direction. Sometimes the forced from these will help pull the remaining stud out. When the hole is perfectly centered, then finish up with the appropriate size based on what is required for the tap.

    Using cutting oil again, drill the center of the broken bolt. Unfortunately, this can be tricky due to the awkward workspace, and depending on the material, sometimes the drill will cut into the softer material, other words not being the remaining bolt so that would damage the existing threads.

    Take your time when drill and try to keep the drill square with the hole.

    If it starts to wander in one direction, you can push it over to the opposite direction or pull the bit slightly. Be careful not to elongate the hole or break the drill bit when doing so. Apply more cutting oil when needed. As mentioned earlier, the cutting fluid keeps the bit cool and reduces the chance of it burning out, keeping it sharp longer.

    Once done, when inspecting the hole you can sometimes see the edge of the threads.

    Apply more cutting fluid and using the correct tap which matches the existing threads, the hole can be cleaned up. Here I am using a straight fluted plug tap because I don’t have much room in behind if I was using a tapered tap. If you’re working with a blind hole, a bottoming tap would be the best option. When using a tap, try to keep it square with the hole. You’ll need to run it in slightly, then loosen slightly, and then run it in some more and repeat. This will help reduce binding, apply more cutting fluid when needed, and don’t force the tap as you can risk breaking it.

    And once done, the threads are as good as new.

    If you’re dealing with a stripped head or in this case, the bolts were seized and the brackets are too soft, so it was causing them to twist. The head of the bolt can be drilled, this would separate the head from the stud so you’re able to remove whatever is being held down. The same process can be used, marking the center with a punch, use a center drill, and then follow up with the correct sized drill bit.

    When done, then you can continue with disassembly and in this case, cleaned up the rust and repainted everything. I do have a video for the full process on that, so be sure to check it out.

    If the bit wanders and you end up damaging the existing threads, this can be fixed but it does require more work. The hole can be welded up and then re-drilled and then tapped again, a threaded insert can be used, or you can go up to a larger sized fastener.

    Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

    © 4DIYers 2013
    All Rights Reserved
    No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

  • How To: Extract Broken off Bolt EVERYTIME!!!

    4:52

    How To Remove a Broken off Bolt! This method works GREAT!! It's best for bolts 1/4 or larger, and the shorter the better, but it sure will surprise you!!

  • Extract remove broken bolt without extractor part 9

    2:50

    Urdu Hindi Arabic #English French Spanish #subtitle
    مشین میں ٹوٹا ہوا بولٹ نکالنے کا طریقہ
    How to extract remove broken bolt without extractor
    टूटी हुई बोल्ट को कैसे निकालना है
    #bababuilder #subtitles
    how to extract bolt
    how to remove bolt
    how to remove bolts that are stuck
    how to remove bolt with broken head
    how to extract broken bolt
    broken bolt removal
    how to remove a broken bolt
    broken bolt
    remove broken bolt
    how to remove broken bolt
    bolt removal
    removing broken bolts
    broken bolt extractor
    removing broken bolt
    removing a broken bolt
    broken bolt removal tool
    sheared bolt removal
    broken bolts
    broken bolt removal tricks
    extracting broken bolt
    broken bolt extraction
    bolt broke
    screw extractor
    how to extract a broken bolt
    broken bolt extractor set
    top broken bolt extractor
    broken screw
    getting broken bolt out
    remove broken stud
    how to remove a broken bolt without a drill
    how to remove a broken bolt without welding
    how to drill out a broken bolt
    how to remove a broken stud
    weld nut to remove broken bolt
    remove broken bolt in deep hole
    remove a broken bolt
    how to remove broken bolts
    remove broken bolt from blind hole

  • How to Remove a Broken Bolt | Broken Bolt Extraction | How to Remove a Broken Bolt | Partzilla.com

    4:24

    See how to remove a broken bolt in this short video from Partzilla.com. Like many of you, John is working in his own shop and socially distancing because of the coronavirus. But he’s still making videos in quarantine.

    We’ll try a couple of bolt extraction methods. First, we’ll try to remove the broken bolt by welding a nut on the end of the bolt. Then we’ll try it a couple more times, but it’s not going to be enough.

    We’ll work on drilling a pilot hole into the bolt and then expanding that hole one bit at a time until we can use a hammer and chisel to get the bolt to collapse on itself so we can remove it. After that, we’ll use a Time-Sert to get some new threads in so we can move on with our job.

    Looking for more little tips? See how to clean fuel injectors:

    Battery problems? Will a multimeter get you some answers or do you need a battery tester?

    Read how to do this job step by step:

    Need aftermarket or OEM parts for your motorcycle, ATV, UTV, and more? How about tools and supplies for your shop? See us at

    Talk to us:
    Twitter:
    Facebook:
    Instagram:

    Looking for engine build videos? Check out our playlist:

  • HOW TO REMOVE BROKEN BOLT IN A DEEP HOLE USING WELDING

    4:35

  • Remove a Broken Exhaust Manifold Bolt - EASY in 15 Minutes! No Disassembly!

    4:25

    This is a tutorial on how to remove a broken off exhaust bolt in a cylinder head without taking it off the engine! You do need to take the exhaust manifold off though. The video applies to any engine regardless of cylinder count.


    If you have a car question ask it completely free at



    *Disclaimer: Please use all safety precautions

  • remove a broken bolt WITHOUT an extraction tool

    1:20

    When you’re working with machines you’re going to break nuts and bolts. This time we didn’t have an extraction tool, it’s easier with an extraction tool but it is possible to extract it with the right size drillbits and the right size tap. In this video I go through the process

  • How To Remove Broken & Rusted Stud Stuck In Aluminum

    5:48

    Manifold studs break, and most extraction methods include drilling it out, and ruining the aluminum threads. Here's a neat way to use a battery and a welder and save your stud threads!



    Merch, Tape Boss & Car Parts
    Tools I like
    Show us your build project
    Help us make awesome stuff

    Twitter
    Instagram
    Facebook

    **If the video was helpful, please give it a thumbs up and consider subscribing.**

    Theme Song: Travelin' by SWIB ( CC BY-SA 3.0
    All Songs:
    Music License: (30-day free trial)


    NO WARRANTIES: All of the information provided in this video is provided AS-IS and with NO WARRANTIES. No express or implied warranties of any type, including for example implied warranties of merchantability or fitness for a particular purpose, are made with respect to the information, or any use of the information, in this video. DEBOSS GARAGE (DG) makes no representations and extends no warranties of any type as to the accuracy or completeness of any information or content of this video.

    DISCLAIMER OF LIABILITY: DG specifically DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES and assumes no responsibility or liability for any loss or damage suffered by any person as a result of the use or misuse of any of the information or content in this video. DG recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. DG assumes or undertakes NO LIABILITY for any loss or damage suffered as a result of the use, misuse or reliance on the information and content of this video.

    USE AT YOUR OWN RISK: This video is for informational purposes only. It is your responsibility to evaluate your own safety and physical condition, or that of your clients, and to independently determine whether to perform, use or adapt any of the information or content in this video. Any automotive repair and/or modification may result in injury. By voluntarily undertaking any task displayed in this video, you assume the risk of any resulting injury; your safety is the sole responsibility of the user and not DG.

  • How To Remove Rounded & Seized Bolts On A Bike | Maintenance Monday

    6:03

    The moment a tool rounds off in the socket, your heart feels like it stops. Simon is here with some bits of advice for removing rounded bolts from bike parts.

    Subscribe to GCN:
    Get exclusive GCN gear in the GCN shop!

    Let us know your methods, hacks and tips for removing rounded bolts in the comments below

    Ex-Professional Cyclist gives you advice and methods of removing those rounded bolt heads on components, using a shoe cleat bolt as an example in this case.

    A hack we were sent in was putting a rubber band over the head of the hex/allen/torx key. The idea is that the rubber band fills the empty space in the rounded off bolt head. Let us know if that works for you

    It is also possible to use a Torx key in the head of a rounded off allen/hex socket, you will normally need to hit the Torx key into the socket, and run the risk of damaging your Torx key…

    Before attempting to remove a bolt with what looks to have a damaged head/socket it is worth soaking the threads in penetrating fluid. Visiting a local hardware store is best for this, as there are some great products out there. Also, Coca-Cola has been known to break down any corrosion too.

    Drilling bolts out is a last resort, ideally a bench drill is used for this so that you get a clean drill through the bolt.

    In this instance, the cleat can be sacrificed. Hacksaw the cleat away from the shoe, and use molegrips to twist/undo the bolt from the thread. Before you do this, soak the bolt in penetrating fluid or similar, overnight.

    Lastly, to help prevent bolts become seized in place, presenting you with rounded off bolt heads/sockets. My personal advice (GCN Jon) is to use a high grade marine grease or copper grease on threads, this will help prevent salt from getting into the threads and causing a rusty joint between the two components.
    A tip we’ve also heard of, on cleats, is to put some silicone sealant in the head/socket of the bolt, this helps prevent foreign objects interfering with the socket. The silicone can then be removed easily with a pick when it comes to time to remove the bolt.

    If you'd like to contribute captions and video info in your language, here's the link ????

    Watch more on GCN...
    How & Where To Use Grease, Fiber Grip, Threadlock + Anti Seize On Your Bike ????
    How To Set Up Cleats For Clipless Pedals ????

    Photos: © Bettiniphoto / & ©Tim De Waele /


    About GCN:

    The Global Cycling Network puts you in the centre of the action: from the iconic climbs of Alpe D’Huez and Mont Ventoux to the cobbles of Flanders, everywhere there is road or pavé, world-class racing and pro riders, we will be there bringing you action, analysis and unparalleled access every week, every month, and every year. We show you how to be a better cyclist with our bike maintenance videos, tips for improving your cycling, cycling top tens, and not forgetting the weekly GCN Show. Join us on YouTube’s biggest and best cycling channel to get closer to the action and improve your riding!

    Welcome to the Global Cycling Network | Inside cycling

    Thanks to our sponsors:

    Alta Badia: // Maratona Dles Dolomites:
    Assos of Switzerland:
    KASK helmets:
    fi’zi:k shoes and saddles: and
    Topeak tools:
    Canyon bikes:
    Quarq:
    DT Swiss:
    Science in Sport:
    Orbea bikes:
    Trek Bicycles:
    Vision wheels:
    Zipp wheels:
    power2max:
    Wahoo Fitness:
    Park Tool:
    Continental tyres:
    Camelbak:

    YouTube Channel -
    Facebook -
    Google+ -
    Twitter -

    Leave us a comment below!

  • How to drill out a hard wheel bolt

    7:36

    Drilling out a wheel bolt is never easy and should always be the last resort. If you do need to drill out a wheel bolt, the easiest way is by using a mag base drill. The wheel bolt in this video is a special anti-theft one and was made from a particularly hard steel alloy. Originally I tried to drill it using a regular HSS drill bit and even a cobalt drill bit but neither of those two would even mark the surface of the bolt. It’s common for anti-theft wheel bolts to be impossible to remove using the dedicated removal bit, probably a major cause of this is when garages fit wheels using impact wrenches instead of torqueing the bolts using a torque wrench.

    Some more videos that might be of interest are-
    How to remove a broken bolt-
    How to remove a rounded Allen head bolt-
    How to remove a stripped screw-
    How to remove a rounded nut or bolt-
    Screw extractors | Easyouts -
    Removing a broken bolt using a welder-
    Remove a broken bolt using a left handed drill bit-

  • How To Remove A Broken Screw/Bolt With A Tap And Die Set

    8:36

    In this short video I show you how remove a broken screw/bolt that broke off inside of the threads! This is a super easy DIY that is a must know how for anyone that works with well, bolts and screws!

    Tap And Die Set -

    Intro/Outro Music -


    I DO NOT OWN ANY RIGHTS TO THE MUSIC IN THE VIDEO, IT IS FOR ENTERTAINMENT USE ONLY!!

  • How to Remove a Stripped Bolt or Nut in a Tight Spot

    8:12

    Get a 3 lb short sledge on Amazon here →
    Here's a link to an appropriate chisel on Amazon →

    How to Remove a Stripped Bolt or Nut in a Tight Spot

  • how to remove damaged stripped screws - DIY hack / broken screw extractor

    4:45

    I will show you 5 different ways to remove damaged / stripped screws or even security screws that you dont have the correct bit for. starting from a few easy hacks to using broken screw extractor ( easy out ) . Like comment and subscribe for more videos. #DIY #howto #billshowto

  • Broken Bolt Extractors and Drill Bits

    17:06

    In a recent SMA video I removed a broken brake bleeder. In the comment section of that video a lot of you asked what kind of broken bolt extractors I used. So much so that i could not answer all of them! So by popular demand here is a video showing you a few of my extraction devices I use. I highlight some of the features I like and dislike about each kind. I also show some of the drills and drill bits I like to use.

    Buy Some Extractors Here :


    Interested in stuff seen in the videos or the tools and toys Eric O. likes and uses? Check out the S.M.A. A-Store and help support the channel! :

    If an SMA Video has helped you out please consider giving using the support link on our YouTube home page. The videos take real time to create and pull us away from real work that pays our bills.
    THANKS!
    --Eric O.


    WANT AN SMA STICKER OF YOUR OWN!?!

    Simply send and E-mail to SMAstickers@outlook.com including: your shipping address and e-mail address in the text, I in turn will send you a paypal invoice for $5 each USA or $6 each international. Let me know how many you want and as soon as the paypal invoice is paid I will ship them out ASAP! Thanks for your support of our channel!!
    --Eric & Vanessa O.



    Feel like sending some swag to SMA because you love the videos but don't know where to send it?

    Just ship it here:

    South Main Auto Repair
    47 S. Main St
    PO Box 471
    Avoca, NY 14809



    Disclaimer:
    Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not South Main Auto Repair.

  • Two Minutes To Remove A Broken Bolt With An Electric Welding | Remove A Broken Bolt

    1:58

  • How To Remove Wheel Hub a Broken Bolt in Deep Hole Using Piston Pin

    4:42

    Thanks for watching
    Like,sub and comment

  • How to REMOVE a broken bolt | LS head bolt or studs

    8:38

    How to remove or extract a broken bolt in a deep recessed hole this works on head bolts studs with an EASY OUT
    We did this on the C10 LS swap we picked up last week.

    #brokenbolt #lsswap

    ****GET YOUR MERCH****


    JUST SEND IT (For anyone that wants to send us stuff)
    PO BOX 157
    Middletown VA 22645

    Keep up with me between uploads on my social media…

    IG: @jd_joyridetv
    FB: JD Joyride TV

    #TeamLaura
    IG: jd_joyridetv_wife

    Bex Russ
    FB: BexRussModel
    IG: bex.russ
    Tw: Bex.Russ

    BIG THANKS TO MY EPIC SPONSORS!!!!

    Get your Octane Booster
    BOOSTane
    save 10% use code: jdjoyride10


    BMR SUSPENSION

    Save 7% Use Code: JOYRIDE7

    ShockerRacing:
    IG: @shockerracing
    FB: ShockerRacing

    Laid Not Sprayed:
    IG: @laidnotsprayed
    FB: LAIDNOTSPRAYEDVINYLWORKZ

    PowerStop Brakes
    AUXBEAM

    YouTube Crew:
    Shocker Racing

    ALL CARS UNITED

    DerekBaranProductions

  • Best way to remove a broken exhaust stud or bolt and save the threads

    14:51

    I often see the question asked “how to remove broken exhaust studs or broken bolts” and save the threads. In my experience, this technique will work on any broken or stripped bolt or stud, not just exhaust. If you don’t have a welder and are using an easy out, the quench technique along with tapping the stud or bolt with a hammer will also greatly improve your chances of success. I just wanted to share how I do it, and it has never let me down. The specific technique I use does require a TIG welder, but I have confirmed you can use this method with flux core or wire feed. The only welder I have is a TIG, so I have never tried other welding disciplines, for the same results. I hope it helps. If you found this video useful please don’t forget to like comment and subscribe. I would greatly appreciate it!!

    If you found this info helpful, or entertaining, please consider subscribing to my channel here.

  • How To Remove A Broken Bolt; Easy Bolt to Remove

    6:44

    Stupid broken bolts, but I got lucky on this one since it was an easy extraction. The process is the same for a difficult removal; Drill a hole down the center of the bolt, insert the extractor, and remove.

  • How to Remove a Broken Bolt

    6:20

    Removing a broken bolt from engine block of Kawasaki Vulcan 900 Custom

  • Weld extracting a broken bolt or stud

    9:30

    Attempt this at your own risk. It is quite possible to damage your work piece with the heat associated with welding.

  • The surprising result after the broken bolt removal and thermostat installation.

    19:46

    On This Video We Showing: The surprising result after the broken bolt removal and thermostat installation. We Clean the surface and Have to cut a little portion on the thermostat housing outlet inner part, to make the thermostat seat and fit right.
    This is The second part of the video Never, Never Use A Drill To Extract A Broken Bolt. Here it is an amazing method!!!


    And! Why You Shouldn't Never, Never Use A Drill. To Extract A Broken Bolt.
    Sometimes When the bolts are too rusted they are hard to remove them and most of the times break,
    We use a different method than the use of drill bit and the twisted extractor tool, because, even if you drill a straight hole all the way throughout the bolt. but if the bolt got a corroded thread it will be so difficult to remove, and you might break the extractor tool too; which will make it more difficult to remove it.
    here Is Another Extracting Bolts Video.

    Thank You For watching my vids.
    Thank you for all the comments.
    I Appreciate the calls that lots of people Throughout the USA makes to my phone number, thanking me for record and upload my videos, it makes me feel proud, that I am helping people to save or to make some money.

    I am making my videos with lots of love and with the meaning of helping you people.
    Thank You For watching my vids.
    Thank you for all the comments.

    Here Is This Link If You Like To contribute. Thank You.


    If you found this video and it was useful,
    Please Like It, And Subscribe To My Youtube Channel.

    So you can help me,
    And I can upload more videos.
    Thank you.

    Thank you for choosing our services.

    We always do our best to serve you better and fix your car properly.

    Your Friendly Expert Automobile Repair Technician.
    With more than 40 years of working in the auto repair field.

    I am working on cars since they have contact points ignition
    and carburetors when most of the built cars came with no air conditioning.

    We Are Here To Help With All Your Auto Repair Needs.
    We have the knowledge and the tools to do the job right.

    Gabriel Auto technician
    413 Highway 100,
    Laguna Heights, TX.
    956 346 3484.

    Auto Repair Shop.
    Auto Air Conditioning Repair and Recharge
    Brakes,
    Tune-Ups,
    Radiators,
    Shock Absorbers,
    Water Pumps,
    Timing Belts,
    Oil Change,
    Fan belts,
    Struts,
    Suspension,
    Transmission Service,
    Computer Diagnostics,
    Paint and Bodywork.
    Iron Welding.

    Thank You for your like on our page @


    Subscribe To My Youtube channel@






  • Remove BROKEN BOLTS with Ease with this Technique

    6:33

    Todays video is a quick tip on how to remove broken bolts. I had 4 that broke off in the flathead engine block and it is time to get them out. With just a spare nut for each broken bolt, everything came out fine.


    #flathead #brokenbolt #fordv8

  • Removing a Broken Bolt Using an Extractor Drill Bit

    3:14

    If you’re like most of us you’ve come across a bolt with a snapped off head, maybe that’s you right now. If you do find yourself dealing with a broken fastener and want to learn how to extract it, you’ve come to the right place. In this episode of Budget Build Garage we demonstrate how we performed the removal of a broken stud from a valve cover, more specifically how to remove a broken stud using the left handed drill bit method. This is just one method to extract a broken screw from the inside of a car engine. The focus is on drilling and tapping out the broken fastener. A bit of advice before we start, and I can’t stress this enough, once the valve cover is removed, you should take precautions not to drop any material into the engine.

    #screwextractor, #brokenbolt, #lefthandeddrillbit

    If you’re into awesomeness, check out our instagram:

  • REMOVING BROKEN VALVE COVER BOLT

    10:36

    HAD A LITTLE PROBLEM FOR A WHILE WITH THE VALVE COVER LEAKING AND JUST NOW GETTING AROUND TO TAKING CARE OF IT, PROCRASTINATION LOL!!

    don't forget to get your T-SHIRTS

  • Broken Stud Removal in Exhaust Manifold

    27:45

    We have an exhaust manifold from a 64 Oldsmobile that has two broken and seized up studs that need to be removed, and also one hole that needs brazed up.

    Paypal Donation:

    Support though Patreon:

    Abom79 t-shirts:

  • How to remove a broken screw or bolt by welding

    5:36

    Easy Tips & Tricks How to remove a broken bolt in the cylinder head
    This is another of the most effective methods and means to remove a broken screw
    into a piece of metal.
    Our channel including guide videos:
    ✓ HOME MADE TOOLS
    ✓ LIFE HACKS
    ✓ HOW TO MAKE TOOLS
    ✓ NEW AND AWESOME IDEAS
    ✓ ADVICE AND TIPS
    ✓ DIY PROJECTS
    ✓ EXPERIENCES


    Watch my second channel @bricolage du cardan
    Click on the following link


    .................................................. .........................................
    You are interested in DIY, crafts or you have nothing
    do, right? You have found the channel you really need. Here you can find lots of crafts,
    handmade items, and the main thing is that they all did shifts and at the lowest cost

    Don't forget to SUBSCRIBE to my channel to receive all of my latest videos.diy recycling
    #Tool #Idea #HYDRAULIC_JACK #DIY #tool_ facts_house

  • Thermostat housing broken bolt leak.... 10/18

    2:03

  • Dealing with Broken Bolts

    4:36

    Brian Eslick from How to Automotive gives you some of his best automotive repair tips on dealing with broken bolts and how to remove them.


    Affiliate link for How to Automotive Tool Store


    New! How to Automotive T-shirts, stickers, and more!


    Website
    For more videos, tips, and to purchase recommended tools and products visit my website at:


    Stay connected at:
    Email: howtoautomotive@gmail.com
    Facebook:
    Google+:
    LinkedIn:




    Disclaimer
    Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brian Eslick. #howtoautomotive

Shares

x

Check Also

Menu